Причина этого неприятного дефекта - износ токопроводящего бушинга (подшипника) ролика переноса. Для устранения дефекта необходимо заменить бушинг на новый. Для снятия/установки бушинга вала переноса аппарат желательно разобрать. Рассмотрим как это сделать на примере МФУ Samsung SCX-4200.
Разборка МФУ Samsung SCX-4200
Выкрутить четыре винта из задней крышки корпусаСнять заднюю крышку и отсоединить разъём вентилятора
Для снятия правой боковой крышки нужно отщёлкнуть три защёлки в верхней части
В нижней части выступы крышки заведены в пазы корпуса
Отсоединить разъём "концевика" передней крышки
Левая боковая крышка корпуса снимается аналогично
Отсоединить разъёмы проводов, идущих к сканеру
Выдернуть эти провода из отверстий корпуса
Снять сканер в сборе и открутить четыре винта верхней крышки корпуса
Снять верхнюю крышку и открутить четыре винта, крепящие блок лазера
Сняв блок лазера, мы получим доступ к тракту прохождения бумаги (который, пользуясь случаем, имеет смысл пропылесосить) и, в частности, к узлу переноса (трансферу)
Вот где собака порылась
Отжав защёлку, удерживающую ролик переноса с торца, извлекаем его вверх и видим бушинг
Извлекаем его
Вот он, виновник неисправности. В интернет-магазинах эта деталь обычно имеет название типа подшипник правый вала переноса ML-1210/1250/SCX-4200/Phaser 3110/3210/WC-3119 , партномер JC72-00102A.
Симптомы следующие: принтер или МФУ Xerox/Samsung (от 2 до 5 минут), бледная печать, двоение/троение изображения,черные или белые полосы. Возможно проблема кроется в неисправности токопроводящей втулки вала переноса и/или сам вал переноса. На примере Xerox 3119 покажем как избавится от этих проблем. Актуально для всех аппаратов типа Samsung SCX-4200, Samsung SCX-4220, Xerox PE114e и тому подобных.
Инструкция по разборке Xerox 3119:
1. Откручиваем винты на задней крышке, снимаем её:
2. Открыв переднюю дверцу, снимаем её с фиксатора. Откручиваем винты боковых крышек.
3. Взявшись за края боковой крышки, тянем ее в низ и на себя, тем самым снимая фиксаторы (обозначены зеленым).
4. Проделываем туже операцию с второй крышкой. Не забывая после отключить разъём (правая крышка).
5. Отключаем все разъёмы. Снимаем блок сканера (верхняя часть)
6. Откручиваем винты крепления верхней крышки.
7. Затем откручиваем винты крепления блока лазера.
8. Отключаем разъёмы блок лазера. Вот мы и добрались до вала переноса (отмечен зеленой полоской)
9. Токопроводящая втулка (выдеоена зелеными полосками)
10. Вдавливаем фиксатор вала переноса (желтая стрелка). Снимаем вал и втулку. Вал необходимо тщательно помыть — с мылом под проточной водой. Далее необходимо вал просушить в теплом (не горячем месте примерно сутки).
11. Перейдем к втулке и пружине под ней. Втулку нужно заменить на новую, а пружину почистить спиртом.
Сама втулка состоит из специального токопроводящего пластика, и со временем теряет свои токопроводящие свойства (высокое напряжение пагубно влияет на структуру материала, а значит и на «проводящие цепочки»). В нормальном состоянии, сопротивление втулки должно составлять от 10 до 100 Ом. Аппарат во время инициализации калибрует блок HVPS по токам, а из-за плохого контакта с валом переноса не может этого сделать полноценно и быстро, и на дисплее мы видим «подождите разогрев ».
Если у Вас нет новой втулки или Вы принципиально хотите произвести ремонт без новых деталей, то применяем следующий способ: втулку (бушинг) нужно обмотать тонкой медной проволокой с небольшим сечением (например проводник МГТФЭ).
Другой вариант изготовления бушинга — самостоятельно выточить из графитовой щетки от двигателя бытового пылесоса, также можно снять с ненужного картриджа НР/Сanon (FCe16) втулку PCR (черную, токопроводящую). Есть рекомендации, что втулку нужно помазать токопроводящей смазкой — чепуха, не нужно, я проверял — налипает тонер и мы там же где и были…
Иногда, при износе втулки, аппарат выходит в готовность очень быстро 5 -15 сек. При этом сопротивление втулки составляет десятки МОм, но печатает бледно — это тоже износ втулки трансфера.
Втулку все же лучше заменить, ее парт-номер JC72-00102A .
Новую или отремонтированную втулку ставим обратно, устанавливаем высохший трансфер, собираем аппарат в обратном порядке — в большинстве случаев имеем отличную печать.
Ремонт мфу принтера XEROX WORKCENTRE 3119
Принтер XEROX WORKCENTRE 3119 обслуживание и ремонт в Москве и области.
Ремонт принтера XEROX WORKCENTRE 3119
Сломался принтер XEROX WORKCENTRE 3119?
Решение есть!
Услуги | Гарантия на работу | Стоимость (руб.) | Выполнение дней |
Диагностика | - | бесплатно | 1 |
Выезд мастера | - | бесплатно | 1 |
Ремонт принтера | 6 месяца | от 2000 | 1-5 |
Профилактика принтера | 2 месяца | от 2000 | 1 |
Замена ремня каретки | 2 месяца | от 2000 | 1-7 |
Замена ролика подачи бумаги | 2 месяца | от 2000 | 1-7 |
Замена каретки | 2 месяца | от 2000 | 1-7 |
Замена платы высоковольтной | 2 месяца | от 2000 | 1-7 |
Замена или восстановление главной платы | 2 месяца | от 2000 | 1-7 |
Замена низковольтной платы | 2 месяца | от 2000 | 1-7 |
Замена печатающей головки | 2 месяца | от 2000 | 1-7 |
Замена шлейфа печатающей головки | 2 месяца | от 2000 | 1-7 |
Настройка принтера | 2 месяца | от 2000 | 1-2 |
Калибровка печатающей головки | 2 месяца | от 2000 | 1-2 |
Прошивка принтера | 2 месяца | от 2000 | 1-2 |
Устранение программных сбоев | 2 месяца | от 2000 | 1-7 |
Чистка печатающей головки картриджа | 2 месяца | от 2000 | 1-7 |
Заправка картриджа | 2 месяца | от 2000 | 1-2 |
Установка СНПЧ | 2 месяца | от 2000 | 1-7 |
Часто случается, что принтер перестает работать должным образом и начинает плохо печатать, или вообще не печатать. Что же делать в данном случае?
Вам нужна помощь профессионального мастера, со знанием своего дела, который проведет диагностику и
Наш технический центр занимается как раз такими поломками. Мы сделаем ваш принтер XEROX WORKCENTRE 3119 рабочим в максимально короткие сроки. Просто наберите и свяжитесь с нами!
Обслуживание принтера XEROX WORKCENTRE 3119
Порядок диагностики и ремонта принтера XEROX WORKCENTRE 3119
Обслуживание принтера Xerox включает замену только качественных запчастей от производителя.
Частые неисправности и ошибки принтеров XEROX WORKCENTRE 3119:
Диагностика мфу XEROX WORKCENTRE 3119 бесплатно
Мы проводим работу по выявлению поломок вашего принтера, внимательно рассматривая все блоки, детали, узлы аппаратов на наличие дефектов, а также определяем объемы работ, необходимые для ремонта принтера, в процессе которой может потребоваться и повторная диагностика.
Важно!
Мы можем предоставить Вам бесплатную удаленную диагностику по телефону. Все необходимые действия вы выполняете по рекомендациям нашего мастера.
Или после звонка, к вам выезжает наш специалист и проводит диагностику принтера. Он выявляет причину, по которой принтер неисправен. Он определяет запчасти, которые требуют замены, выставляет счет на нужные детали и после оплаты выставленного счета, выполняет ремонт и замену нужных запчастей принтера.
Можно ли обойтись без диагностики?
Конечно же, нет. Без диагностики невозможен любой ремонт любой техники. А наши мастера, знающие свое дело, могут установить причину поломки в максимально короткие сроки как у нас, так и по месту эксплуатации, что позволяет сэкономить ваше и наше время.
Что если поломка появится снова?
Наши специалисты являются профессионалами, и после их работы у Вас навряд ли что-либо опять сломается. Но все же, если так получилось, то мы готовы предоставить Вам гарантию от нашего сервисного центра, а также на замененные запчасти от производителя.
Принтер может сломаться по многим причинам, вот одни из них: загрязненные узлы аппаратов принтера, неработоспособность картриджей, неработоспособности печатающих головок, неправильная работа тракта прохождения бумаги, неправильная работа узла очистки головок, поломка в результате установки СНПЧ, неправильная парковка каретки.
Мы ремонтируем XEROX WORKCENTRE 3119 и другие принтеры.
Xerox WorkCentre 3119 — многофункциональное устройство (принтер, сканер, копировальный аппарат) черно-белая лазерная печать до 18 стр/мин, формат печати A4.
В Xerox WorkCentre 3119 используется картридж 013R00625.
Ресурс картриджа 013R00625 – 3000 страниц.
Картридж Xerox WorkCentre 3119 хорошо заправляется.
Вы можете заправить картридж 013R00625 для Xerox WorkCentre 3119
у нас в сервисном центре на Павелецкой, ул. Дубининская, дом 68.
Основные неисправности Xerox WorkCentre 3119
- Xerox WorkCentre 3119
не подает бумагу из лотка
При долгой работе Xerox WorkCentre 3119 начинает плохо подавать бумагу из лотка. Это связано с износом ролика подачи бумаги. Ролик подачи бумаги покрыт мелким рисунком, который стирается во время работы от контакта с бумагой. Ролик вращается – проскальзывает по бумаге, и не подает ее в аппарат. Необходимо очистить ролик от загрязнений или заменить его на новый.
Каталожный номер насадки на ролик захвата бумаги из кассеты — JC72-01231A (YC72-01231A). - Xerox WorkCentre 3119 застревает бумага на выходе
В Xerox WorkCentre 3119 тонер закрепляется на бумаге в узле термозакрепления. Закрепление происходит за счет температуры и давления резинового вала на тефлоновый вал. Тефлоновый вал выполнен в виде пустотелого металлического цилиндра покрытого тефлоном (как тефлоновая сковородка). Покрытие необходимо чтобы тонер не пригорал к поверхности тефлонового вала. Тефлоновое покрытие вала со временем стирается, и тонер начинает налипать на вал, при этом изображение на копии может смазываться. Бумага начинает часто застревать в узле термозакрепления, на выходе из аппарата. Необходимо заменить тефлоновый вал или узел термозакрепления в сборе.
Каталожный номер тефлонового вала Xerox WC 3119 — JC66-00601A | 022N01610.
Каталожный номер резинового вала Xerox WC 3119 — JC66-00600A | 022N01611.
Каталожный номер узла термозакреплния Xerox WC 3119 — JC96-03891C | JC96-03891A. - Xerox WorkCentre 3119
бледно печатает
Необходимо заменить картридж, заправить картридж, очистить блок лазера аппарата.
Все работы можем выполнить на территории заказчика. Для клиентов, находящихся в ближайших районах от нашего офиса на Павелецкой предоставляются скидки на ремонт Xerox WC 3119.
Цены на услуги
в нашей компании.
Наш сервисный центр профессионально разбирается в вопросах ремонта и обслуживания принтеров и многофункциональных устройств Xerox.
Мы сможем выполнить качественный
ремонт Xerox WC 3119 в Москве.
Наша компания начала работать в 1997 году, опыт и ответственность наше преимущество. Все наши инженеры имеют высшее техническое образование, и имеют стаж работы по ремонту офисной техники более 22 лет! Все ремонтные работы проводятся в соответствии с нормативами, мы используем только качественные запчасти для ремонта офисной техники.
Первичную диагностику неисправности офисной техники наши инженеры смогут сделать по телефону, и сказать точную стоимость ремонта. Многолетний опыт работы наших специалистов позволяет безошибочно определять неисправности.
Мы выполняем ремонт принтеров в Москве с выездом к заказчику. Вам не придется тратить драгоценное время и средства на транспортировку крупной техники в мастерскую и беспокоиться о ее сохранности, все работы мы выполним на вашей территории. Наш инженер может выполнить оперативно работу у Вас в офисе или дома. Стоимость ремонта Вы сможете оплатить наличным и безналичным расчетом. В нашем сервисном центре Вы всегда можете купить оригинальные тонер картриджи к офисной техники Xerox. Доставка по Москве.
Срочный Xerox в Москве у метро Павелецкая.
Стоимость
Ремонт принтеров
Ремонт МФУ
Ремонт копировальных аппаратов
Тип копировального аппарата | Диагностика копировального аппарата в нашем сервисном центре |
Диагностика копировального аппарата на выезде у заказчика | Ремонт копировального аппарата в нашем сервисном центре | Ремонт копировального аппарата на выезде у заказчика |
Копировальные аппараты формата А4 до 20 коп./мин. | 400 | 1000 | 1000 | 2500 |
Копировальные аппараты формата А4 свыше 20 коп./мин. | 400 | 1000 | 1000 | 2500 |
Копировальные аппараты формата А3 до 20 коп./мин. | 400 | 1000 | 1500 | 2500 |
Копировальные аппараты формата А3 свыше 20 коп./мин. | 400 | 1000 | 1500 | 2500 |
Копировальные аппараты формата А3 свыше 40 коп./мин. | 400 | 1000 | 2000 | 3500 |
Цветные копировальные аппараты | 600 | 1500 | 2000 | 3500 |
Инженерные машины А0 | 800 | 2000 | 4000 | 6000 |
Заправка картриджей HP
№ картриджа | модель аппарата | цена заправки | цена восстановлени |
Q2612A | 1010/1015/1018/ 1020/1022/3015/3030/ 3050/3055/M1005 |
500 | 1000 |
C4092A | 1100 / 3200/3220 | 500 | 1100 |
C7115A | 1000 / 1005/1200/3380 | 500 | 1000 |
C7115X | 1000 / 1005/1200/3380 | 700 | 1200 |
Q2613A | 1300 | 500 | 1000 |
Q2613X | 1300 | 700 | 1200 |
Q2624A | 1150 | 500 | 1000 |
Q5949A | 1160 / 1320 | 500 | 1000 |
Q5949X | 1320 | 700 | 1200 |
Q7553A | P2015/M2727 | 500 | 1000 |
Q7553X | P2015/M2727 | 700 | 1200 |
C4096A | 2100 / 2200 | 600 | 1200 |
Q2610A | 2300 | 800 | 1300 |
Q6511A | 2410 /2420/2430 | 800 | 1400 |
Q6511X | 2410/2420/2430 | 1100 | 1700 |
Q7551A+ЧИП | P3005 | 800 | 1400 |
Q7551X+ЧИП | P3005 | 1200 | 1800 |
C4127X | 4000 /4050 | 1000 | 1600 |
C8061A | 4100 | 800 | 1400 |
Q1338A | 4200 | 1500 | 2100 |
Q1339A | 4300 | 1500 | 2100 |
Q5942A | 4250 /4350 | 1000 | 1600 |
C4129X | 5000 /5100 | 1300 | 2000 |
Q7516A+ЧИП | 5200 | 1100 | 1800 |
Q7570A+ЧИП | M5025/M5035 | 1100 | 1800 |
CF214A | 1100 | 1800 | |
CF214X | LaserJet Enterprise 700 Printer M712dn, M712xh | 1500 | 2200 |
C3909A | 5Si/8000 | 1100 | 1800 |
C4182X | 8100 | 1300 | 2000 |
C8543X | 9000/9040/9050 | 1900 | 2600 |
CE 278A | P1566/1606 | 500 | 1000 |
CE285A | P1102 | 500 | 1000 |
CB435A | P1005/P1006 | 500 | 1000 |
CB436A | P1505/M1120/M1522 | 500 | 1000 |
CE 505A | P2035/P2055 | 500 | 1000 |
CE 505X | P2055 | 700 | 1200 |
CE255A | P3015 | 600 | 1200 |
CE255X | P3015 | 900 | 1500 |
CC364A | P4014/P4015/P4515 | 1000 | 1700 |
CC364X | P4015/P4515 | 1400 | 2100 |
CE390A | Enterprise M4555/M601/M602/ M603 |
1000 | 1700 |
CE390X | Enterprise M4555/M602/ M603 |
1400 | 2100 |
CZ192A | Pro M435 | 1100 | 1800 |
Заправка картриджей Brother
Модель принтера Brother | Картридж | ресурс | Цена, руб. |
DCP 7010, 7010R, 7020, 7025, 7025R, FAX 2820, 2825, 2825R, 2920, 2920R, HL 2030, 2030R, 2040, 2040R, 2070, 2070N, 2070NR, MFC 7225, 7225N, 7420, 7420R, 7820, 7820N, 7820NR, 7820R | TN 2075 | 2000 | 600 |
DCP 8040, 8040LT, 8045, 8045D, 8045DN, HL 5130, 5140, 5140LT, 5150, 5150D, 5150DLT, 5170, 5170DN, MFC 8040, 8045, 8045D, 8045DN, 8220, 8440, 8840, 8840D, 8840DN, 8840LT | TN 3030 TN 3060 | 3500 6500 | 900 1200 |
HL 2035, 2035R | TN 2085 | 1500 | 600 |
DCP 7030, 7030R, 7032, 7032R, 7040, 7045, 7045NR, HL 2140, 2140R, 2142, 2142R, 2150, 2150N, 2150NR, 2170, 2170W, 2170WR, MFC 7320, 7320R, 7440, 7440N, 7440NR, 7840, 7840W, 7840WR | TN 2135 TN 2175 | 1500 2000 | 600 |
DCP 8060, 8065, 8065DN, HL 5200, 5240, 5250, 5250DN, 5270, 5270DN, 5280, 5280DW, MFC 8460, 8460N, 8860, 8860DN, 8860N, 8870, 8870DW | TN 3130 TN 3170 | 3500 5000 | 900 1200 |
HL2130R/DCP7055R | TN-2080 | 700 | 600 |
Brother HL-1112R/DCP-1512R/HL-1110R/DCP-1510R/MFC-1810R/MFC-1815R (новинка) | TN-1075 | 1000 | 600 |
HL-2240R/ 2240DR/ 2250DNR/ DCP-7060DR/ 7065DNR/ MFC-7360NR/ 7860DWR | TN-2235 TN-2275 | 1200 2600 | 600 600 |
HL-5340D/5350DN/5350DNLT/ 5370DW/5380DN для DCP-8070D/8085DN для MFC-8370DN/8380DN/8880DN/8890DW | TN-3230 TN-3280 | 3000 8000 | 900 1200 |
Заправка картриджей Samsung
Номер картриджа | Модель аппарата | Стоимость заправки | Стоимость восстановления |
MLTD101S | ML-2160/2165/2168/ SCX-3400F/3405F/3407 1.5К (ЧИП) | 900 | 1400 |
MLTD103S/L | ML-2950/2955/SCX-4728/4729 1,5/ 2,5 К (ЧИП) | 800 | 1200 |
MLTD104S | ML1660/ 1665/SCX3200/ 3205 1,5 К (ЧИП) | 800 | 1200 |
MLTD105L | ML1910/ 1915/ML2525/2580N/ SCX4600/4623F/SF-650 2,5 К (ЧИП) | 800 | 1200 |
MLTD105S | ML1910/ ML2525/SCX4600 1,5 К (ЧИП) | 800 | 1200 |
MLTD106S | ML2245 2K. (ЧИП) | 800 | 1200 |
MLTD108S | ML1640/1645/2240/2241Black 1,5K (ЧИП) | 800 | 1200 |
MLTD109S | SCX4300 2 К (ЧИП) | 900 | 1300 |
MLTD111S | Xpress SL-M2020/SL-M2022/SL-M2022W/SL-M2070 1K (ЧИП) | 900 | 1500 |
MLT-D115L | Xpress SL-M2620/SL-M2620D/SL-M2820/SL-M2820ND/SL-M2820DW 3K | 1200 | 1600 |
MLTD117S | SCX-4650M/4655FN 2,5K (ЧИП) | 900 | 1400 |
MLTD203E | M3820/3870/4020/4070 | 1500 | 1800 |
MLTD205L | SCX4833/ML3310 5К (ЧИП) | 900 | 1300 |
MLTD205S | SCX4833/ML3310 2К (ЧИП) | 800 | 1100 |
MLTD209L | ML2855ND/ SCX4824FN/4828 5К (ЧИП) | 900 | 1300 |
MLTD209S | ML2855ND/ SCX4824FN/4828 2К (ЧИП) | 800 | 1100 |
ML1210D3 | ML1210/ ML1250/ML1430 2,5К | 500 | 800 |
ML1520D3 | ML1520P/ ML1720 3K | 500 | 800 |
ML1610D2 | ML1615 2K | 500 | 800 |
MLD1630A | ML1630/ SCX4500 2K (ЧИП) | 700 | 1100 |
ML1710D3 | ML1510/ ML1710/ML1750 3К | 500 | 1100 |
ML2010D3 | ML2015/ ML2510/ML2570 3К (предохр.) | 600 | 1000 |
ML2150D8 | ML2150/ ML2151N/ML2152W 8К (ЧИП) | 900 | 1300 |
ML2250D5 | ML2250/ ML2251N/ML2252W 5К (ЧИП) | 800 | 1200 |
ML2550DA | ML2550/ ML2551N/ML2552W 10К (ЧИП) | 1000 | 1300 |
MLD2850A | ML2850D/ ML2851ND 2К (ЧИП) | 700 | 1100 |
MLD3050A | ML3050/ ML3051N 4К (ЧИП) | 800 | 1200 |
MLD3050B | ML3050/ ML3051N 8К (ЧИП) | 900 | 1300 |
MLD3470A | ML3470D/ ML3471ND 4К (ЧИП) | 900 | 1300 |
MLD3470B | ML3470/ 3471ND 10К (ЧИП) | 1000 | 1400 |
ML3560D6 | ML3560/ ML3561N 6К (ЧИП) | 800 | 1200 |
SCX4100D3 | SCX4100 3К | 500 | 800 |
SCXD4200A | SCX4200 3K (ЧИП) | 600 | 1000 |
ML4500D3 | ML4500 2,5К | 600 | 1000 |
SCX4521D3 | SCX4321/ SCX4521F 3К (предохранитель) | 600 | 1000 |
MLD4550A | ML4550/ ML4551N 10К (ЧИП) | 1000 | 1400 |
MLD4550B | ML4550/ ML4551N 20К (ЧИП) | 1500 | 1900 |
SCX4720D3 | SCX4720 3К (ЧИП) | 800 | 1200 |
SCX4720D5 | SCX4720 5К (ЧИП) | 900 | 1300 |
SCXD4725A | SCX4725F/SCX4725FN 3К (ЧИП) | 700 | 1100 |
SF5100D3 | SF5100/ SF5100P 2,5К | 500 | 800 |
SCX5312D6 | SCX5112/SCX5312F 6K (ЧИП) | 1200 | 1600 |
SCXD5530A | SCX5330N/ SCX5530FN 4К (ЧИП) | 900 | 1300 |
SCXD5530B | SCX5330N/ SCX5530FN 8К (ЧИП) | 1000 | 1400 |
SCX6320D8 | SCX6122FN 8K (ЧИП) | 1200 | 1800 |
ML6060D6 | ML1440/ ML6040/ML6060 6К (ЧИП) | 900 | 1300 |
ML7300DA | ML7300N 10К (ЧИП) | 1500 | 1900 |
Заправка картриджей Xerox
Модель принтера, ресурс | Номер картриджа | Цена заправки |
Phaser 3010/3040/WC3045 (3К) | 106R02183 (ЧИП) | 600 |
Phaser 3100 + смарт карта (3К) | 106R01378/106R011379(смарт-карта) | 900 |
Phaser 3110/3210 (3К) | 109R00639 | 500 |
Phaser 3116 (3К) | 109R00748 (предохр.) | 600 |
Phaser 3117/3122/3124/3125 (3К) | 106R01159 (предохр.) | 600 |
Phaser 3120/3121/3130 (3К) | 109R00725 | 500 |
Phaser 3140/3155/3160 (2.5К) | 108R00908/108R00909(ЧИП) | 600 |
Phaser 3150 (3.5/5К) | 109R00746/109R00747(ЧИП) | 700 |
Phaser 3200 (2/3К) | 113R00735/113R00730 (ЧИП) | 600 |
Phaser 3250 (3.5/5К) | 106R01373/106R01374 (ЧИП) | 700 |
Phaser 3300 (8К) | 106К01411/106К01412(ЧИП) | 800 |
Phaser 3310 (6К) | 106R00646 | 700 |
Phaser 3400 (6/8К) | 106R00461/106R00462 | 700 |
Phaser 3420/3425 (5/10К) | 106R01033/106R01034(ЧИП) | 900 |
Phaser 3428 (4/8К) | 106R01245/106R01246 (ЧИП) | 800 |
Phaser 3435 (5/10К) | 106R01414/106R01415 (ЧИП) | 900 |
Phaser 3500 (6/12К) | 106R01148/106R01149 (ЧИП) | 1000 |
Phaser 3550 (5К) | 106R01529 (ЧИП) | 800 |
Phaser 3600 (7/14/20К) | 106R01370/106R01371/106R01372 | 1100 |
Phaser3635 (10К) | 108R00794/108R00796(ЧИП) | 1000 |
Phaser 4400 (10/15К) | 113R00627/113К00628 | 1000 |
Phaser 4510 (10/19К) | 113R00711/113R00712 | 1000 |
Phaser 5335 (10К) | 113R00737 | 1000 |
Phaser 5400 (20К) | 113R00495 | 1300 |
WC-312/M15 (6К) | 106R00586 | 800 |
WC-3119 (3К) | 013R00625 (ЧИП) | 600 |
WC3210/3220 (4.1К) | 106R01485/106R01487(ЧИП) | 700 |
WC-4118 (8К) | 006R01278(ЧИП) | 800 |
WC-M20 (8К) | 106R01048 (ЧИП) | 800 |
WC-PE16 (3.5К) | 113R00667 (предохр.) | 600 |
WC-PE114 (3К) | 013R00607 | 500 |
WC-PE120 (3.5/5К) | 013R00601/013К00606 (ЧИП) | 700 |
WC-PE220 (3К) | 013R00621 (ЧИП) | 700 |
P8EX (5К) | 603P06174 (113R00296) | 700 |
Заправка картриджей Kyocera
МОДЕЛЬ АППАРАТА | РЕСУРС | ЦЕНА Заправки в сервисном центре руб. | |
TK-100 | KM-1500 | 6000 | 1 000 |
TK-110 | FS-720 / 820 / 920 / 1016 | 6000 | 1 000 |
TK-1100 | FS -1110 / 1024MFP / 1124MFP | 2100 | 700 |
TK-110E | FS-720 / 820 / 920 / 1016 | 2000 | 700 |
TK-1110 | FS -1040, FS-1020MFP / FS-1040MFP / FS-1120MFP | 2500 | 700 |
TK-1120 | FS-1060 / FS-1025MFP / FS-1125MFP | 3000 | 750 |
TK-1130 | FS -1030MFP / 1130MFP | 3000 | 750 |
TK-1140 | FS -1035MFP / 1135MFP | 7200 | 1 100 |
TK-120 | FS-1030D | 7200 | 1 100 |
TK-130 | FS-1028 / 1128 / 1300 / 1350 | 7200 | 1 100 |
TK-140 | FS-1100 | 4000 | 850 |
TK-160 | FS-1120 | 2500 | 700 |
TK-17 | FS-1000 / 1010 / 1050 | 6000 | 1 000 |
TK-170 | FS-1320 / FS-1370 | 7200 | 1 100 |
TK-18 | FS-1018 / 1020D | 7200 | 1 100 |
TK-310 | FS-2000 / FS-3900 / FS-4000 | 12000 | 1 500 |
TK-3100 | FS-2100 | 12500 | 1 550 |
TK-3110 | FS-4100 | 15500 | 1 800 |
TK-3130 | FS-4200 / FS-4300 | 25000 | 2 550 |
TK-320 | FS-3900 / 4000 | 15000 | 1 750 |
TK-330 | FS-4000 | 20000 | 2 200 |
TK 340 | FS 2020 | 12000 | 1 500 |
TK-350 | FS-3040 / FS-3920 / FS-3140 / FS-3540 / FS3640 | 15000 | 1 750 |
TK-360 | FS-4020 | 20000 | 2 200 |
TK-410 | KM-1620 / 1635 / 1650 / 2020 / 2035 / 2050 | 15000 | 1 750 |
TK-435 | TASKalfa 180 / 181 / 220 / 221 | 15000 | 1 750 |
TK-440 | FS-6950 | 12000 | 1 500 |
TK-450 | FS-6970 | 15000 | 1 750 |
TK-475 | FS-6025MFP / 6030MFP | 15000 | 1 750 |
TK-55 | FS-1920 | 15000 | 1 750 |
TK-6305 | TASKalfa 3500i / 4500i / 5500i | 35000 | 3 450 |
TK-65 | FS-3820 / 3830 | 20000 | 2 200 |
TK-675 | KM-2540 / 3040 / 2560 / 3060 | 20000 | 2 200 |
TK-685 | TASKalfa 300i | 20000 | 2 200 |
TK-70 | FS-9100 / 9120 / 9500 / 9520 | 40000 | 3 850 |
TK-710 | FS-9130 / 9530 | 40000 | 3 850 |
TK-715 | KM-3050 / 4050 / 5050 | 34000 | 3 450 |
TK-725 | TASKalfa 420i / 520i | 34000 | 3 450 |
TK-4105 | TASKalfa 1800 / 1801 / 2200 / 2201 | 15000 | 2 300 |
Оплата и доставка
Важную роль для нас играют интересы каждого клиента. Именно поэтому мы предлагаем удобные способы оплаты услуг и товаров: наличными или посредством перечисления денежных средств на наш расчетный счет (реквизиты мы предоставим по индивидуальному запросу после получения заявки). Обратите внимание, что мы осуществляем оперативную доставку курьером по Москве, при этом ее стоимость умеренная. Кроме того, у нас налажено сотрудничество с проверенной транспортной компанией, которая выполняет перевозку в любые населенные пункты России. Можете полностью на нас положиться!
Схема работы
Обязательно позвоните нам, или оставьте заявку на сайте или по e-mail.
Нередко устранить мелкий дефект в работе оборудования возможно по телефону.
В сложных случаях инженер выезжает на диагностику к заказчику с целью определения окончательной стоимости ремонта.
Только при Вашем согласии выполняется ремонт. Оплатить ремонт Вы сможете как за наличные, так и по безналичному расчету.
Мы предоставляем гарантию на выполненные работы.
Наши инженеры имеют стаж работы более 20 лет, они смогут диагностировать неисправность по телефону с определением стоимости ремонта и, при необходимости, запасных частей. В результате Вам будет понятна целесообразность ремонта.
- Page 1 WORKCENTRE 3119 SERVICE MANUAL Part Number 708P88471 06/06... Page 2 Xerox service documentation is intended for use by certified, product trained service per- sonnel only. Xerox does not warrant or represent that it will notify or provide to such customer any future change to this documentation. Customer performed service of equipment, or modules, components or parts of such equipment may affect whether Xerox is responsible to fix machine defects under the warranty offered by Xerox with respect to such equipment.
- Page 3 Section Contents ........................2-1 3. Image Quality Section Contents ........................3-1 4. Repairs/Adjustments Section Contents ........................4-1 5. Parts List Section Contents ........................5-1 6. General Procedures/Information Section Contents ........................6-1 7. Wiring Data Section Contents ........................7-1 WorkCentre 3119 06/06... Page 4 Introduction Page intentionally blank 06/06 WorkCentre 3119...
- Page 5 High voltages and lasers inside this product are dangerous. This machine should only be serviced by a suitably trained and qualified service engineer. 2. Use only Xerox replacement parts There are no user serviceable parts inside the machine. Do not make any unauthorized changes or additions to the machine, these could cause the machine to malfunction and create electric shock or fire hazards.
- Page 7 Take care not to cut or damage the power cable or plugs when moving the machine. 9. Use caution during thunder or lightning storms. Xerox recommend that this machine be dis- connected from the power source when such weather conditions are expected. Do not touch the machine or the power cord if it is still connected to the wall socket in these weather condi- tions. Page 8 5. Do not place candles, burning cigarettes, etc. on the machine, these could cause a fire. Assembly / Disassembly Precautions Replace parts carefully, always use Xerox parts. Take care to note the exact location of parts and also cable routing before dismantling any part of the machine. Ensure all parts and cables are re- placed correctly.
- Page 9 Alternatively, employ a commercially available wrist strap device, which should be removed for your personal safety reasons prior to applying power to the unit under test. WorkCentre 3119 06/06... Page 10 4. Dispose of used batteries according to the manufacturers instructions. Toner Cartridge Service Only toner cartridges supplied by Xerox should be used. Printing defects or set damage caused by the use of non-approved print cartridges or un-licensed toner refills are not covered by the guar- antee.
- Page 11 How to identify a refilled toner cartridge. One way security screws are used in the manufacture of the cartridge – check if these are dam- aged. WorkCentre 3119 06/06...
- Page 13 Fund all field retrofits. 1. Field Service Operations shall: a. Preserve the Xerox product involved and the scene of the incident inclusive of any associ- ated equipment located in the vicinity of the incident. b. Return any affected equipment/part(s) to the location designated by Xerox EH&S and/or the Business Division. Page 14 Introduction Page intentionally blank. 06/06 WorkCentre 3119...
- Page 15 Service Call Procedures 1. Service Call Procedures SCP 1 Service Call Actions .......................1-3 SCP 2 Final Actions .........................1-4 WorkCentre 3119 06/06... Page 16 Service Call Procedures Page intentionally blank 06/06 WorkCentre 3119...
Page 17: Scp 1 Service Call Actions
All cables are connected correctly. 4. If available, check the machine service log book for any previous actions that may be relevant to the call. 5. Review any defective print or copy samples. 6. Perform ‘1 Initial Checks RAP’. WorkCentre 3119 06/06...Page 19: Table Of Contents
11 Paper Empty RAP ......................2-15 12 Cover Open RAP ........................2-16 13 No Power RAP ........................2-17 14 SPOOL Error RAP ......................2-18 15 Abnormal Noise RAP ......................2-19 16 Scanning RAP ........................2-20 17 Print Cartridge Problems RAP ....................2-21 18 Software Problems RAP .....................2-22 WorkCentre 3119 06/06...Page 21: Initial Checks Rap
Try printing a test page from a computer. --> If there is an error, check cables and driver installation. 5. Check the Print Quality. Is there a Print Quality Problem? --> Go to Section 3, Image Quality. WorkCentre 3119 07/06...
Page 22
1. Use only paper which is of suitable quality, weight and size. See the user guide. 4. Check the overall condition of the machine 1. Clean the Paper Transport areas. Any rollers with dirt surfaces should be cleaned. If necessary, install new rollers. 07/06 WorkCentre 3119...
Page 23: Jam 0 Rap
(Isopropyl Alcohol) or water. Install a new pickup roller, PL 4 if necessary. 4. Check the solenoid HB (Pickup), PL 3 by 4. Install a new solenoid HB (Pickup), PL 3 if using ‘Pickup Test’ in Engine Test Mode, GP damaged. WorkCentre 3119 07/06...
Page 24
7. Install new parts as necessary. Test Mode, GP 4. Check the motor harness Motor harness, PL 1 and connectors, PL 1 and stepper motor Drive assembly, PL 6 (drive), PL 6. Main PBA, PL 1 07/06 WorkCentre 3119...
Page 25: Jam 1 Rap
2. If paper is jammed in front of or inside the 2. Install new parts as necessary: fuser, PL 5. Exit sensor actuator, PL 4 SMPS/HVPS, PL 1 Main PBA., PL 1 WorkCentre 3119 07/06...Page 27: Multi-feeding Rap
3. Use paper with a smoother surface finish. 4. Check the solenoid HB (pickup) operation 4. Install new parts as necessary: using Engine Test Mode, GP 4. Solenoid HB (Pickup), PL 3 Main PBA, PL 1 WorkCentre 3119 07/06...- Page 29 Check and Cause Solution 1. Paper is out of specification. 1. Clear the jam, refer to GP 6. Use paper within specification. Refer to the User Guide. Recommend the use of good quality ‘long grain’ paper. WorkCentre 3119 07/06 2-11...
Page 31: Lsu Error Rap
Check the LSU operation using Engine Test Mode, GP 4. 2.The LSU, PL 1 is damaged. Install new parts as necessary: LSU, PL 1 3. Check the LSU HSYNC signal using Main PBA, PL 1 Engine Test Mode, GP 4. WorkCentre 3119 07/06 2-13...Page 33: Paper Empty Rap
Note: The Paper Empty Sensor is mounted onto the SMPS/HVPS, PL 1. 3. The SMPS/HVPS or Main PBA, PL 1 is 3. Install new parts as necessary: faulty. SMPS/HVPS, PL 1 Main PBA, PL 1 WorkCentre 3119 07/06 2-15...Page 35: No Power Rap
Power supply cord, PL 1 Test Mode, GP 4. SMPS/HVPS, PL 1 Main PBA, PL 1 2. LCD panel does not come on but normal 2. Install a new PBA sub-panel, PL 8. start up sounds are heard. WorkCentre 3119 07/06 2-17...Page 37: Abnormal Noise Rap
Engine Test Mode, GP 4. Toner Fan, PL 1 Check the Step Motor (Drive) connector on LSU, PL 1 the Main PBA, PL 1. Motor Assembly, PL 6 Main PBA, PL 1 WorkCentre 3119 07/06 2-19...Page 39: Toner Low
When this message occurs, there are approximately 1,000 pages left. Expired Toner Cartridge - Explanation: The toner cartridge mechanical life is expired. - Solution: Install a new toner cartridge, PL 1. WorkCentre 3119 07/06 2-21...- Page 41 1. Refer the customer to the WorkCentre install the correct printer driver and to select 3119 User Guide. the WorkCentre 3119 as the default printer. 2. Ensure you have sufficient free hard disk 2. The message "insufficient printer memory" space for the temporary work files created means there is a hard disk space problem on during printing. Page 42 1. Printer Driver Error. 1. Ensure that the correct driver is loaded. Use the driver supplied on the CD or down- loaded from the Xerox.com. DO NOT use the Microsoft driver supplied with the Windows operating system. If the machine is a GDI...
- Page 43 IQ 14 Contamination on Back of Page ..................3-16 IQ 15 Blank Page Print out (1) ....................3-17 IQ 16 Blank Page Print out (2) ....................3-18 IQ 17 Defective Image Quality ....................3-19 IQ 18 Printed Vertical Lines Not Straight .................3-20 IQ 19 Blurred Image ........................3-21 WorkCentre 3119 06/06...
Page 45: Iq 1 Vertical Black Lines And Bands
1. Install a new toner cartridge, PL 1 deformed doctor-blade in the toner and retest. cartridge, PL 1. 2. Scratched surface of the charge 2. Install a new toner cartridge, PL 1 roller in the toner cartridge, PL 1. and retest. WorkCentre 3119 06/06...Page 47: Iq 3 Horizontal Black Band
2. Clean all the gears on the toner development process may be con- cartridge, PL 1. taminated. If the problem still persists, replace Charge Roller = 37.8mm the Toner Cartridge, PL 1. Supply Roller = 44.9mm Develop Roller = 35.2mm Transfer Roller = 45.3mm WorkCentre 3119 06/06...Page 49: Iq 5 Light Image
8. Develop roller is contaminated 8. Install a new toner cartridge, PL when the toner has almost depleted. 9. Check the HVPS output using 9. If necessary, install a new SMPS/ Engine Test Mode, GP 4. HVPS, PL 1. WorkCentre 3119 06/06...Page 51: Iq 7 Uneven Density
1, gently shake it and replace. blade. 2. The transfer roller, PL 1 is 2. Adjust the transfer roller, PL 1. improperly installed 3. The life of the toner cartridge has 3. Install a new toner cartridge, PL expired. WorkCentre 3119 06/06...Page 53: Iq 9 Ghost (1)
5. Bad contacts caused by contamina- 5. Clean the SMPS/HVPS contact tion from toner particles between IPR- terminals. If the problem persists, P-Terminal CON, PL 3 and the SMPS/ install a new SMPS/HVPS, PL 1. HVPS contacts, PL 1. WorkCentre 3119 06/06 3-11...Page 55: Iq 11 Ghost (3)
PL 5. CAUTION Take care not to deform the rollers. 2. Possible abnormal voltage and 2. Install a new toner cartridge, PL bad contact of the terminal of the supply roller in the toner cartridge, PL 1. WorkCentre 3119 06/06 3-13...Page 57: Iq 13 Contamination On The Face Of Page
Check and Cause Solution 1. The transfer roller, PL 1 maybe 1. Run Clean Drum, GP 3 several contamInated. times. 2. Toner leakage due to improperly 2. Install a new print cartridge, PL 1. sealed developer. WorkCentre 3119 06/06 3-15...Page 59: Iq 15 Blank Page Print Out (1)
HVPS, PL 1 Toner cartridge, PL 1 4. The CIS harness may be faulty. 4. Check the CIS harness. Install new parts as necessary: Scan assembly, PL 7 Main PBA, PL 1 WorkCentre 3119 06/06 3-17...Page 61: Iq 17 Defective Image Quality
Check shading profile Perform shading test in tech mode, GP 5. Check the gap between original and scanner glass, PL A gap of more than 0.5mm can cause blurred images. Ensure the cover is closed correctly. WorkCentre 3119 06/06 3-19...Page 63: Iq 19 Blurred Image
1. Check the gap between original and platen glass, PL 1. A gap of more than 0.5 mm can cause a blurred image. Ensure rollers and cover close correctly. Install new parts as necessary, PL 7. WorkCentre 3119 06/06 3-21...
Page 64
Image Quality Page intentionally blank 3-22 06/06 WorkCentre 3119...
- Page 65 REP 15 CRUM PBA ........................4-21 REP 16 Transfer Roller ......................4-21 REP 17 Feed Roller ........................4-22 REP 18 Pickup Roller, Solenoid HB (Pickup) and Solenoid HB (Bypass) ......4-24 REP 19 Exit Roller ........................4-25 REP 20 Drive Assembly ......................4-26 WorkCentre 3119 06/06...
Page 67: Rep 1 Front Cover
Electricity can cause death or injury. Moving parts can cause injury. 1. Remove the cassette assembly, Figure 1. Figure 3 Figure 1 2. Open the front cover, Figure 2. Figure 2 WorkCentre 3119 06/06...Page 69: Rep 3 Fuser Fan
Moving parts can cause injury. 1. Remove the Rear Cover. (Refer to REP 2) 2. Release the harness from the Harness Holder. Remove 1 screw, then the Har- ness Holder, Figure 1. Figure 2 Figure 1 WorkCentre 3119 06/06...Page 71: Rep 5 Left Side Cover
Electricity can cause death or injury. Moving parts can cause injury. 1. Remove the Front Cover. (Refer to REP 2. Remove the Rear Cover. (Refer to REP 2) 3. Remove 1 screw, Figure 1. Figure 4 Figure 1 WorkCentre 3119 06/06...- Page 73 Figure 2 Note: When replacing the Scan Assembly, push down the Stopper-M-Lever to ensure the ScanAssembly fits into the Middle Cover. 5. Lift the Platen Cover upwards then remove the Platen Cover, Figure 3. Figure 5 Figure 3 WorkCentre 3119 06/06... Page 74 Scan Upper Unit to Belt and Carriage, Figure 9. the Scan Lower Unit, Figure 7. Figure 9 12. Disconnect the CIS FFC from CIS. Remove 2 sliders from each end of the Figure 7 4-10 06/06 WorkCentre 3119...
- Page 75 15. Remove the Spring then the Idle Bracket in the direction of the arrow, Figure 13. Figure 11 Note: Take note of the position of the notch to ensure correct replacement when fitting the Scanner Belt into the Carriage. Figure 13 WorkCentre 3119 06/06 4-11...
Page 77: Rep 8 Middle Cover Unit
Electricity can cause death or injury. Moving parts can cause injury. 1. Remove the Scan Assembly. (Refer to REP 6) 2. Remove 4 screws, then the Middle Cover Unit, Figure 1. Figure 4 Figure 1 WorkCentre 3119 06/06 4-13...- Page 79 Cover-M-Fuser, Figure 6. Figure 3 5. Remove 2 screws. Disconnect the Fuser Harness and the Fuser Joint Harness from the Halogen Lamp. Remove the Hal- ogen Lamp by sliding it to the left, Figure Figure 4 Figure 6 WorkCentre 3119 06/06 4-15...
Page 81: Rep 11 Toner Fan
3. Remove the Right Side Cover. (Refer to REP 4) 4. Disconnect CON 3 from the SMPS/HVPS. 5. Remove 1 screw, then the Toner Fan. Figure 1. Figure 2 5. Remove 4 screws, then the LSU, Figure Figure 1 Figure 3 WorkCentre 3119 06/06 4-17...Page 83: Rep 13 Main Pba
Electricity can cause death or injury. Moving parts can cause injury. 1. Remove the Engine Shield Assembly. (Refer to REP 12) 2. Disconnect CN 4. Remove 2 screws, then the Main PBA, Figure 1. Figure 3 Figure 1 WorkCentre 3119 06/06 4-19...Page 85: Rep 15 Crum Pba
(Refer to REP 12) Earth, Figure 1. 3. Remove 4 screws, then the CRUM PBA, Figure 1. Figure 1 3. Disconnect the PTL PBA Harness then remove the PTL Holder and PTL Lens, Figure 2. Figure 1 WorkCentre 3119 06/06 4-21...- Page 87 Idle Shaft, Figure 2. 2, Figure 4. Figure 4 Figure 2 6. Remove the Feed Gear 1 Assembly and 4. Remove 3 screws then the Feed Bracket, Feed Roller 1, Figure 5. Figure 3. Figure 5 Figure 3 WorkCentre 3119 06/06 4-23...
Page 89: Rep 19 Exit Roller
2. Use a screwdriver to remove the Exit Gear and Bearing, then remove the shaft and rollers, Figure 1. Figure 2 4. Remove 2 screws, then the Solenoid HB (Bypass) and Pickup Solenid HB (Pickup), Figure 3. Figure 1 Figure 3 WorkCentre 3119 06/06 4-25...- Page 91 PL 4 Frame Assembly (2) ......................5-8 PL 5 Fuser Unit ........................5-10 PL 6 Drive Assembly ......................5-12 PL 7 Scan Assembly ......................5-14 PL 8 OPE Assembly .......................5-16 PL 9 Cassette Assembly ......................5-18 PL 10 Common Hardware & General Service Items ..............5-20 WorkCentre 3119 06/06... Page 92 Spare Parts List PL 1 Main Assembly 06/06 WorkCentre 3119...
- Page 93 Spare Parts List PL 1 Main Assembly Item Part Number Description Remark WORKCENTRE 3119 ELA HOU BASE-HOUSING USB CABLE REFER TO PL 10, ITEM 5 105N02072 CBF-POWER CORD FRAME ASSEMBLY REFER TO PL 3, ITEM 0 127N07521 TONER FAN (DC_HAWK) Page 94 Spare Parts List PL 2 Housing Base Assembly 06/06 WorkCentre 3119...
- Page 95 ADJUST RACK-M-MANUAL GEAR-RACK_PINION 002N02613 RIGHT SIDE COVER REP 4 COVER-M-SIDE R COVER OPEN MICRO SWITCH 002N02612 LEFT SIDE COVER REP 5 002N02611 REAR COVER REP 2 COVER-M-REAR COVER-M-REAR DOOR 127N07354 FUSER FAN (DC 24V) REP 3 152N11729 HOLDER-M_HARNESS WorkCentre 3119 06/06... Page 96 Spare Parts List PL 3 Frame Assembly (1) 06/06 WorkCentre 3119...
- Page 97 REFER TO PL 5, ITEM 0 GUIDE-M-TR LOWER IPR-P-GROUND_FUSER SPRING ETC-GUIDE DEV LABEL(R)-HV FUSER 022N02131 BRACKET-P-FEED SPRING-TS 130N01375 CAM-M-PICK_UP IPR-GROUND_DRIVE IPR-GROUND_DRIVE2 RING-CS 121N01088 SOLENOID HB (BYPASS) REP 18 130N01376 SOLENOID HB (PICKUP) REP 18 RUBBER SEAT 032N00434 PMO-PLATE GUIDE DEV LEFT WorkCentre 3119 06/06... Page 98 Spare Parts List PL 4 Frame Assembly (2) 06/06 WorkCentre 3119...
- Page 99 PMO-GEAR PICKUP B 17-2 PMO-GEAR PICKUP A 17-3 SPRING-CS BUSH-M-FEED_IDLE SPRING-ETC TR SHAFT-FEED IDLE 038N00409 GUIDE PAPER IPR-P-GROUND_GUIDE PAPER 115N00854 IPR-P-EARTH TRANSFER 062N00259 PTL LENS HOLDER-PTL 140N62968 PTL PBA PMO-BUSHING TR R SPRING ETC-TR LEFT HAWK BUSH-M-TR-LEFT SHAFT FEED WorkCentre 3119 06/06... Page 100 Spare Parts List PL 5 Fuser Unit 5-10 06/06 WorkCentre 3119...
- Page 101 130N01380 THERMISTOR 122N00256 LAMP-HALOGEN 220V 122N00246 LAMP-HALOGEN 110V 022N02267 HEAT ROLLER GEAR-FUSER BUSH-M-HR R BUSH-M-HR L ROLLER-M-EXIT F/UP RMO-RUBBER_EXIT 022N02268 PRESSURE ROLLER BEARING-PRESSURE SPRING-CS PMO-BUSHING TX HOLDER-ACTUATOR SPRING 120N00461 EXIT SENSOR ACTUATOR IPR-P-FRAME_FUSER GUIDE-M-INPUT LABEL(P)-CAUTION HOT WorkCentre 3119 06/06 5-11... Page 102 Spare Parts List PL 6 Drive Assembly 5-12 06/06 WorkCentre 3119...
- Page 103 Description Remark 007N01551 DRIVE ASSEMBLY REP 20 BRACKET-P-GEAR 1400 GEAR-DRV FUSER IN GEAR-HUB CLUTCH GEAR-DRV FUSER OUT WASHER PLAIN GEAR-RDCN 113/33 GEAR-RDCN 57/18 BRACKET-P-MOTOR 1400 GEAR-RDCN 90/31 GEAR RDCN 103/41 STEPPER MOTOR (DRIVE) PMO-IMPELLER_DRV MACHINE SCREW WorkCentre 3119 06/06 5-13... Page 104 Spare Parts List PL 7 Scan Assembly 5-14 06/06 WorkCentre 3119...
- Page 105 007N01549 BELT-TIMING GEAR GEAR-M_PULLEY CBF SIGNAL-CIS HARNESS 130N01484 CIS (CONTACT IMAGE SENSOR) BELT 002N02618 COVER SCAN LOWER SHEET-SCAN LOWER BRACKET-P-PULLEY PULLEY-M_IDLE SPRING-CS SLIDER-M_CIS R SLIDER-M_CIS L ELA UNIT-OPE BELT CLIP CIS SUPPORT BAR CIS BRACKET SPRING WorkCentre 3119 06/06 5-15... Page 106 Spare Parts List PL 8 OPE Assembly 5-16 06/06 WorkCentre 3119...
- Page 107 Spare Parts List PL 8 OPE Assembly Item Part Number Description Remark OPE ASSEMBLY REP 7 002N02619 COVER-M-PANEL 002N02620 OPE PANEL 003N01015 KEY-M-MENU 003N01013 KEY-M-START 003N01014 KEY-M-STOP KEY-M-COPIES 021N02253 CAP-M-LED 101N01405 PBA SUB-PANEL DISPLAY SCREEN HARNESS OPE WorkCentre 3119 06/06 5-17... Page 108 Spare Parts List PL 9 Cassette Assembly 5-18 06/06 WorkCentre 3119...
- Page 109 PL 9 Cassette Assembly Item Part Number Description Remark 050N00497 CASSETTE ASSEMBLY ADJUST-M-CASSETTE_L ADJUST-M-CASSETTE_R GEAR-PINION 019N00820 IPR-PLATE 019N00821 RPR-FRICTION PAD SHEET-HOLDER PAD 019N00822 HOLDER-M-PAD SPRING ETC-LOCKER PLATE-P-KNOCK_UP SPRING-CS PMO-EXTENSION SMALL GUIDE-M-EXTENSION FRAME-M_CASSETTE BRACKET SPRING ROLLER SPRING CASSETTE-COVER_SIDE WorkCentre 3119 06/06 5-19...
- Page 111 GP 11 System Block Diagram ....................6-44 GP 12 Tools ..........................6-45 GP 13 Acronyms and Abbreviations ..................6-46 GP 14 Selecting Printer Locations ..................6-48 GP 15 Sample Test Pattern ....................6-49 GP 16 Restriction of Harzardous Substances (RoHS).............6-50 GP 17 Service Log ........................6-51 WorkCentre 3119 06/06...
Page 113: Product Overview
GP 1 Product Specifications Product Overview Table 1: Item Description Remark Basic Model WorkCentre 3119 Target User Personal users Key Specification -18ppm(Ltr. 19ppm), Chorus2(CPU: Use 16/32 Bit RISC Processor) -Flash memory: 1Mb -USB 2.0 -250 pages input, 50 pages output...Page 115: Paper Handling Specifications
Bypass 60.2 - 161.78gsm (16 - 43lb) Paper Path Standard output Bottom to Top Front (FIFO) Straight Through Face up, Single sheet Paper Size 216 x 356mm (8.5 x14 inches) 76 x 127mm (3 x5 inches) Compatibility WorkCentre 3119 06/06...
Page 116
Table 9: Item Description Owner’s manual Yes (Electronic) S/W CD-ROM 1 CD for User Manual, Smart Thru 4, Print Driver, Scan Driver, Toner cartridge 1 EA Power cable 1 EA Telephone jack Printer cable Type 1 piece 06/06 WorkCentre 3119...
- Page 117 General Procedures and Information Consumables Table 10: Item Description Toner installation method Front loading Toner life 1K - Initial 3K - Running Toner Count Level Sensor Software Count WorkCentre 3119 06/06...
- Page 119 General Procedures and Information Rear view Figure 2 Control panel Figure 3 WorkCentre 3119 06/06...
- Page 121 - The temperature of the fuser cover"s surface is maintained at less than 80°C to protect the user and a caution label is attached where the customer can see it easily when the rear cover is opened. WorkCentre 3119 06/06 6-11... Page 122 In other words, after the /HSYNC signal is detected the image data is sent to the LSU to adjust the left margin on the paper. Figure 5 6-12 06/06 WorkCentre 3119...
- Page 123 - OPC Cleaning: Electrostatic process - Management of waste toner: Electro static process(Cleanerless Type) - OPC Drum protecting Shutter: No - Classifying device for toner cartridge: ID is classified by interruption of the frame channel Figure 6 WorkCentre 3119 06/06 6-13... Page 124 General Procedures and Information Hardware Structure and Descriptions The WorkCentre 3119 can be broken down to several elements which are; the Main PBA, OPE Assembly, Scan Assembly, Print Engine, Copier and the power supply. Each element is a sepa- rated Module which focuses on the common and standard design for different kind products.
- Page 125 General Procedures and Information Main Control-ASIC Figure 8 WorkCentre 3119 06/06 6-15... Page 126 Used as Page Buffer in Printing, Scan Buffer in Scanning and System Working Memory Area - Size: 8Mbyte - 3.5 MB: System Working Memory Area and Scan Buffer - 4.5 MB: Printing System Working Memory Area - Max Frequency: 133MHz 6-16 06/06 WorkCentre 3119...
- Page 127 - White Data output Voltage: 1.7V -(Mono Copy, 5ms/line) Copier Part Copy Mode: Black and White Scanner Type: CIS with Flatbed/Platen Maximum Size of Original: Platen: 216 x 297 mm (max. width = 216 mm, max length = 297 mm) WorkCentre 3119 06/06 6-17... Page 128 - Output Voltage Rising Time: 50 ms Max - Output Voltage Falling Time: 50 ms Max - Output Loading range: 30 M - 1000 M - Output Control Signal(MHV-PWM) : CPU is HV output when PWM is Low 6-18 06/06 WorkCentre 3119...
- Page 129 CON2 CON2 5V Pin 3,4,24 24V Pin 13 24VS PIN 11, 12 GND Pin 5,6 GND Pin 7,9,10 GND Pin 7,9,10 Rated Output +5V +/-5% +24V+/-15% +24V+/-15% (4.75-5.25V) (21.6-27.6) (21.6-27.6) Max. Current Output 1.0A 0.5A 1.0A WorkCentre 3119 06/06 6-19... Page 130 On the other hand, when the signal is off, the PC102 is off, the voltage is cut off at the gate of the Triac. The Triac switches off, and then the heat lamp is switches off. Triac (THY1) feature:12A, 600V SWITCHING Phototriac Coupler (PC102) 6-20 06/06 WorkCentre 3119...
- Page 131 General Procedures and Information - Turn On If Current: 15mA - 50mA(Design: 16mA) - High Repetive Peak Off State Voltage: Min 600V Software Structure and Descriptions Architecture The following diagram shows the Engine Control System. Figure 3 WorkCentre 3119 06/06 6-21... Page 132 Engine Unit Control Module Engine Unit Control Module consists of 4 sub-functions. Regulating temperature Fan control Sensor status management Unit and Devices Control (Motor, Clutch, etc.) 6-22 06/06 WorkCentre 3119...
- Page 133 General Procedures and Information Paper Size The WorkCentre 3119 does not have a paper size sensor. If the paper width is narrow, the tem- perature of the fuser roller does not uniformly conform to the overall surface of the roller. So in this case, the engine controls the interval of pick up of the paper. Page 134 LSU Ready Check The WorkCentre 3119 feeding mechanism will pick up paper when the LSU is ready. When the paper is sensed by the feed sensor, the engine control module checks whether the LSU and Hsync is ready for an appointed time.
- Page 135 When the engine receives a sleep command, it stops the operation of the fuser and the fan unit in the engine. The main system then sets the engine to a sleep state. A user can select WorkCentre 3119 06/06...
- Page 137 Hsync error. If this happens, the engine stops all functions and keeps the error state. The engine then reports the error status to the main system. The error message is then displayed on the LCD notifying the user. WorkCentre 3119 06/06 6-27... Page 138 Default Change Darkness Light/Normal/Dark Normal Original Type Text, Text/Photo, Photo Reduce/Enlarge Original (100%) 100% A4>LTR (94%) EXE>LTR (104%) 150% 200% Custom: 50-200% No. of Copies Timeout 15,30,60,180 sec, Off 30 sec 8. Report System Data 6-28 06/06 WorkCentre 3119...
- Page 139 Stop/Clear. Toner Save This option allows the machine to reduce the amount of toner used on each page. To access this option, press the menu button until ’Special Copy’ appears on the display. Use the but- WorkCentre 3119 06/06 6-29... Page 140 To access this option, press the menu button until ’Maintenance’ appears on the display. Use the buttons to scroll between the options available. Press the enter but- ton to confirm selection or to scroll down another level. Or, to return to standby mode, press Stop/ Clear. 6-30 06/06 WorkCentre 3119...
Page 141: Gp 4 Engine Test Mode
THV EN/NEG Test (SMPS/HVPS, PL 1) 1:On, 2:Off (-1000V+/- 300V/-150V) THV ON (1300V) (SMPS/HVPS, PL 1) 1:On, 2:Off (+1300V+/- 20V) THV ADC 1300V (SMPS/HVPS, PL 1) 1:On, 2:Off THV ADC 600V-3550V (SMPS/HVPS, PL 1) 1:On, 2:Off (Compare each ADC value) WorkCentre 3119 06/06 6-31...- Page 143 Or, to return to standby mode, press Stop/Clear. -System Data: Prints the printer’s specifications and settings. -Error Info: Prints a list of all errors WorkCentre 3119 06/06 6-33...
Page 145: Clearing Paper Jams
In the Paper Tray 1. Open and close the front cover. The jammed paper is automatically ejected from the machine. If the paper is not ejected continue to step 2. 2. Pull the paper tray open. Figure 2 WorkCentre 3119 06/06 6-35...Page 147: In The Fuser Area Or Around The Toner Cartridge
8. Close the rear cover. 9. Open and close the front cover to resume printing. In the Fuser Area or Around the Toner Cartridge Note: The fuser area is hot. Take care when removing paper from the machine. WorkCentre 3119 06/06 6-37...
Page 148
In the Bypass Feeder Bypass Jam appears on the display when you try to print using the bypass feeder and the machine does not detect paper, due to no paper or improper paper loading. The error message may also 6-38 06/06 WorkCentre 3119...
- Page 149 In that case, pull the paper out of the machine. Figure 9 In the Toner Cartridge Remove the paper while turning the toner cartridge drum against the feed direction. WorkCentre 3119 06/06 6-39...
Page 151: Gp 8 Periodic Defective Image
44.9mm Light or dark horizontal image bands Developing Roller 35.2mm Horizontal band image Transfer Roller 45.3mm Image Ghost Heat Roller 64.0 Black image and image ghost Pressure Roller 75.3mm Black spot on the backside Figure 1 WorkCentre 3119 06/06 6-41...Page 153: Gp 10 Led Status Indicator
Blinking slowly: Priner Data Comm. Blinking fast: Printing Blinking normally: Copy, Scan, etc. Error: Toner empty, Paper jam, Paper Empty, Cover Open Blink Case of recoverable error: Paper mismatching Case of warming up state: Replace toner WorkCentre 3119 06/06 6-43...Page 155: Gp 12 Tools
Standard: "-" type, "+" type (M3 long, M3 short, M2 long, M2 short). Spring Hook Standard: For general use Tweezers Standard: For general home use, small type. Software (Driver) installation CD ROM Cotton Swab Standard: For general home use, for medical service. WorkCentre 3119 06/06 6-45...- Page 157 Quick Printer Initiating Device Qt’y quantity Random Access Memory Read Only Memory Second Cassette Feeder SMPS Switching Mode Power Supply Spool Simultaneous Peripheral Operation Online switch sync synchronous or synchronization Universal Serial Bus WECA Wireless Ethernet Compatibility Alliance WorkCentre 3119 06/06 6-47...
Page 159: A4 Iso 19752 Standard Pattern
The life of the print cartridge, developer cartridge and printing speed are measured with the pat- tern shown below of 5% area coverage. The pattern is shown at approximately 70% of actual size. A4 ISO 19752 Standard Pattern Figure 1 WorkCentre 3119 06/06 6-49...Page 161: Gp 17 Service Log
General Procedures and Information GP 17 Service Log Service Log Use the service log to record all service procedures. WorkCentre 3119 06/06 6-51...
Page 162
General Procedures and Information Page intentionally blank 6-52 06/06 WorkCentre 3119...
- Page 163 WD 12 SMPS -110V (2/4) .......................7-14 WD 13 SMPS -110V (3/4) ......................7-15 WD 14 SMPS -110V (4/4) .......................7-16 WD 15 SMPS -220V (1/4) ......................7-17 WD 16 SMPS -220V (2/4) ......................7-18 WD 17 SMPS -220V (3/4) .......................7-19 WD 18 SMPS -220V (4/4) .......................7-20 WorkCentre 3119 06/06... Wiring Diagrams WD 16 SMPS-220V (2/4) Figure 16 7-18 06/06 WorkCentre 3119...
Page 181: Wd 17 Smps -220v (3/4)
Wiring Diagrams WD 17 SMPS-220V (3/4) Figure 17 WorkCentre 3119 06/06 7-19...- Page 183 Wiring Diagrams Page intentionally blank WorkCentre 3119 06/06 7-21... Page 184 Page 1 of 2 APPENDIX A: Health & Safety Incident Report Involving a Xerox Product Customer Identification Customer Name: Name of Customer Contact Person: Address: E-mail: Telephone: Fax: Customer Service Engineer Identification Name: Employee: Pager: Location:...
- Page 185 E-Mail: Mailing Address: Date Report Submitted: Instructions: E-mail or fax this completed form to EH&S: ž For incidents in Xerox Europe and Developing Markets East (Middle East, Africa, India, China, and Hong Kong) please e-mail: [email protected] or fax: +44 (0) 1707 35 3914 Note: - If you fax this form, please also send original by internal mail ž...